丛林树屋灯光安装教程
Ju ng le Tree House Light Insta ll ation tuto ria l
丛林树屋灯光安装教程
Ju ng le Tree House Light Insta ll ation tuto ria l
打开A包
将积木拆起
Ope n th e A pack age
Remov e th e blo ck s
拿出配件,从U S B出来第一个灯粒放配件内安
装如下
Tak e out the acce ss ories, leave th e USB a nd f it the
ac cessorie s in si de Install the follo wi ng
将导线藏于积木内并还原积木
Keep the wires in the blocks and rest or e the b lo cks
将第二个灯粒安装如下
将积木拆起
Inst al l th e sec ond lamp partic le as f ol lo ws
Re mo ve the bl ocks
把第三个灯粒安装如下
把导线藏于积木内安装还原
Insta ll th e th ir d lam p par ticle as follow s
Ke ep th e wi re hi dden in the bu ilding b lo ck s to
i ns tall and restore
将积木拆起,把导线延箭头方向穿过
把灯粒如图安装在积木处
Re mo ve the bl ocks and cross thr ou gh t he le ad
extens io n arr ow
I nstall t he l amp part ic les at the bui lding bloc k
→
剩下的导线延箭头方向穿过
T he remaini ng wi re p as ses through with th e
e xtensi on ar ro w di rectio n
→
积木拆起,把灯粒安装如下
Remov e th e bui ld ing blocks a nd i ns ta ll th e la mp s
as f ol lows
打开B包
将从U S B出来的第一个灯组安装如下
Ope n the B packag e
The first ligh t set c om in g out o f the U SB is
insta ll ed as f ol lo ws
将多余导线绕子啊树枝上
Put the extra wire s arou nd th e br anches
安装第二个灯组
→
→
将剩下导线穿过积木如图
Ins ta ll th e se cond light set
Pas s th e rem ai ning wires t hro ug h the bu il ding
blo ck s in Fi g
安装第三个灯组
打开C包
Ins ta ll th e th ird li ght set
Open the C package
拿出配件,把灯粒安装如下
Take out the accesso ri es and install the lamps a s foll ow s
将积木拆起
Remove t he b lo ck s
将从U S B出来的灯粒安装如下
将导线延箭头方向穿过
Ins ta ll the la mps coming o ut o f the USB as follows
Rou te th e wi re ex te nsion arrow thro ug h
将积木拆起,安装第二个灯粒
Remove th e buil di ng blocks and insta ll a seco nd l am p par ticle
→
将导线穿过
Pass the wire throug h
→
将导线穿过
Pass the wire throu gh
→
积木拆起,安装第三个灯粒
Remove the buil di ng blocks and instal l a thir d lam p pa rti cle
→→
将最后一个灯粒安装如下
Install t he l as t lam p pa rt icle as fo llows
打开D包
Open the D package
拿出第一个房顶
将U S B出来的第一个灯组安装如下
Take o ut the firs t roo f
I ns tall the first light set comin g out o f the USB as follo ws
→
将U S B导线延箭头方向穿过,第二个灯组的
导线穿到下一个屋顶
安装第二个灯组
Cross t he USB wire e xte nsi on ar row throu gh t he se co nd la mp
set The wire runs throu gh th e ne xt ro of
Ins ta ll th e se cond light s et
将积木拆起把灯粒安装如下
Re mo ve t he bu il ding block s an d ins ta ll the lam ps as fo llows
把多余导线穿过屋内
Put the exce ss wi re t hr ou gh the house
穿到第三个屋顶,安装第三个灯组
最后一个灯粒安装如下
Wear to a th ird ro of and install a third ligh t se t
Th e la st la mp pa rt icle is install ed as fo ll ow s
打开E包
Op en th e E pac ka ge
把树还原
将灯组安装在最顶部的4个树枝上
Re store the tree
I nstall t he lamp set on the top 4 bra nches
将灯组安装如下
Install t he la mp s et as f ollo ws
→
→
→
→