89151中世纪酒馆灯光安装教程
89151 Medieval tavern lighting installation tutorial
89151中世纪酒馆灯光安装教程
89151 Medieval tavern lighting installation tutorial
灯光材料如下
灯光组导线分布图
1
2
3
4
5
6
7
8
9
10
注: 导 7 8 线的灯光组是两节2灯
Lighting materials are as follows
Lighting group wire distribution diagram
Note: The light group of w 7 8 ires is two sections of 2 lights
1
2
3
4
拿出第一组灯光导线 1 2 3 4
来到酒馆二层位置,将 导1 线的灯光组安装如下
Take out the first set of light wires 1 2 3 4
Go to the second floor of the tavern and install the lighting
group of wire a 1 s follows
2
拿出 导2 线的灯光组
Take out the w 2 ire lighting group
将第三层顶部拆起
Remove the top of the third layer
将 导线上的灯光组如图穿到顶部并安装
在拆起的积木上
2
Thread the light group on the w 2 ires to the top and install
将积木安装还原
拿出撬开器或者镊子把积木拆起如下
Install and restore building blocks
Take out a pry or tweezers and remove the blocks as follows
把 导2 线穿过积木如下图并将积木安装还原
Pass wires through the building blocks as shown below
and install and restore the building blocks
2
拿出 导线的灯光组
4
3
3 4
Take out the w 3 4 ire light group
如图,延箭头方向将灯光组穿过
As shown, extend the arrow direction through the light group
将 导3 线的灯光组安装如下
3
4
Install the light group of w 3 ires as follows
把 导线上的灯光组延箭头方向穿到隔壁
4
4
将灯光组安装如下
4
Thread the light group on wire in the direction of
the arrow to the next door
4
Install the light group as follows
拿出第二组灯光导线5 6 7 8
9
10
5
6
7
8
10
7
注: 导8 线的灯光组是两节2灯
将所有灯光导线延箭头方向穿过积木
9
Take out the second set of light wires 5 6 7 8 9 10
Note: The light group of w8 ires is two sections of 2 lights
7
Run all light wires through the blocks in the arrow direction
5
将 导5 线的灯光组安装如下
6
6
剩下的灯光导线延箭头方向穿过并安装
导线的灯光组如图
6
Install the light group of w 5 ires as follows
The remaining light wires pass through the arrow direction
and install the light group of w 6 ires as shown in the figure
7
8
9
10
剩下的灯光导线分布图
7
8
拿出 导线的灯光组
7
8
The rest of the light wiring map
Take out the w 8 ire light group
7
延箭头方向从旁边穿过
再从第三层的上方箭头位置穿下
Follow the arrow through the side
And then through the top arrow of the third layer
将导线拉到旁边位置如箭头所示
将三层的顶部拆起
Pull the wire to the side as indicated by the arrow
Remove the top of the three levels
7
8
把 导 7 8 线的灯光组安装如下
将积木安装还原
Install the light group of wire a 7 8 s follows
Install and restore building blocks
拿出 导线的灯光组如图
9
9
10
10
如图将二层的桌子拆起
Take out w 9 10 ire lighting group as shown
As shown in the picture, remove the table on the second floor
把 导 9 10 线和灯光组延箭头方向穿过并还原桌子
将 导9 线的灯光组安装在第一层如图
9
10
Put the wires and lights through the arrow direction
and restore the table
9 10
Install the light group of w 9 ires on the first layer as shown
10
最后将 导10 线的灯光组延箭头方向穿过
将最后一个灯光组安装如下
Finally, the light group of the wire is extended through
the direction of the arrow
10
Install the last light group as follows
最后将电池盒装入电池,USB接口连接到电池盒上
放置在下图位置
Finally, install the battery box into the battery, connect
the USB interface to the battery box and place it in the
following position